Bang & Olufsen BeoVision 6 Service Manual Page 50
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4.10 Service mode
M2 INFORMATION Sub Menu
This menu contains information about software versions for the teletext processor.
STB TIMER 1 and 2 : It is possible to adjust the delay to an Set Top Box connected.
This is because certain Set Top Boxes has a long start-up time. As this may affect a
timer recording it is possible to alter the start-up time between 0 and 255 seconds.
HW STATUS: For factory use.
RESET TO DEFAULT
WARNING
The reset to default command is activated directly when the menu is highlighted.
If the menu item “RESET TO DEFAULT” is selected, the text “PLEASE WAIT” is
displayed until the above functionality has been carried out. While the text
“PLEASE WAIT” is displayed, you must NOT carry out source selection and you
must not press EXIT or STANDBY.
Following parameters are affected, when the device is resat:
- Option is programmed to 2 if FM module is present, else option 1
- AV1 and AV2 are configured as “NONE”
- PL speakers are configured as “NONE”
- Volume preset is configured to default
- Max volume is configured to default
- Bass, treble and balance are configured to default
- Loudness is set to “NO”
- AVC is enabled
- Brightness, contrast and color adjustments are configured to default
- Movie mode is enabled
- Comb filter is enabled
- Stored TV and Radio programs are deleted
- Modulator frequency is configured to default
- Stored program groups are deleted
- Stand is configured to default position
- WUT data is deleted
- The clock is configured to synchronise to program 1
- Autoformat is enabled
- WSS is enabled
- Default format for 4:3 signals is set to 16:9 pan
- Format 5 (4:3) is set to ENABLED
- Production counters stops
- Power down functionality is enabled
- Menu language is configured to English
- Internal Radio is ENABLED if FM module is present
- First install menu will be shown next time the device is powered up
TV SERVICE MENU
In this menu, it is possible to change the MF variant (i.e. activate/deactivate
different tuner systems) and change band limits and constants.
AFC can be set on/off in order to allow IF ADJUST adjustment. AFC off is
remembered only until power down.
When the system is selected, the band limits and constants are NOT changed.
Frequencies are in MHz.
TUNER TAKEOVER adjusts the tuner’s agc. The value range is 0-63. When replacing
ABO-CENTER v/HENRIKSENS ELEKTRONIK
- BeoCenter 6 – 26 1
- Survey of modules 1.1 3
- Survey of modules 3
- 1.2 How to service 4
- How to service 4
- How to service 1.3 5
- 1.4 How to service 6
- How to service 1.5 7
- PIN-code 7
- 1.6 How to service 8
- Fault flow chart 2.1 9
- Fault flow chart 9
- 2.2 Fault flow chart 10
- Fault flow chart 2.3 11
- 2.4 Fault flow chart 12
- Fault flow chart 2.5 13
- 2.6 Fault flow chart 14
- Fault flow chart 2.7 15
- 2.8 Fault flow chart 16
- Fault flow chart 2.9 17
- 2.10 Fault flow chart 18
- Fault flow chart 2.11 19
- 2.12 Fault flow chart 20
- Fault flow chart 2.13 21
- 2.14 Fault flow chart 22
- Fault flow chart 2.15 23
- 2.16 Fault flow chart 24
- Fault flow chart 2.17 25
- 2.18 Fault flow chart 26
- Fault flow chart 2.19 27
- 2.20 Fault flow chart 28
- Fault flow chart 2.21 29
- 2.22 Fault flow chart 30
- Adjustments 32
- ServiceTool 37
- Service mode 4.1 41
- Service mode 41
- 4.2 Service mode 42
- CUSTOMER SERVICE MENU 42
- Service mode 4.3 43
- Service mode in general 43
- 4.4 Service mode 44
- Service mode 4.5 45
- 4.6 Service mode 46
- Service mode 4.7 47
- 4.8 Service mode 48
- Service mode 4.9 49
- 4.10 Service mode 50
- Service mode 4.11 51
- 4.12 Service mode 52
- Service mode 4.13 53
- 4.14 Service mode 54
- IC INFORMATION 55
- MSP 02170A48 55
- PICTP 00 55
- 4.16 4.164.16 56
- 15. Geometry check 58
- 12. Geometry check 59
- 5.4 Replacement of LCD 60
- - Remove all cables 61
- - Remove socket cover 61
- - Remove speaker cover 61
- Correct mounted! 61
- + 5.5 Mount servicestands 64
- - Remove screws 64
- 5.9Replace Main chassis 65
- - Remove LCD shield 66
- - Remove LCD plugs 66
- - Remove plug from scaler 66
- - Remove cover 66
- 5.11 67
- Replace Main chassis 67
- Menu - BeoSound 3200 68
- 1. Update Software 68
- 2. HDR-A backup 68
- 3. . . . 68
- 4. . . . 68
- 5.13Replace LCD 69
- 5.14 Replace LCD 70
- 5.15 71
- + 5.5 Mount service stands 73
- - Remove cables 73
- Attention! 74
- - Remove fan 77
- - Remove screw 77
- - Remove as shown 80
- - Placement of PCB51 80
- - Remove cable 81
- DVI-I plug 90
- Type survey 91
- Type survey 6.5 91
- Video Input formats 92
- 6.6 Video Input formats 92
- Wiring diagram 93
- Available parts 94
- Available parts 8.2 95
- Survey of screws and washers 96
- Available parts 8.4 97
- 8.5 Available parts 98
- Base 4090 98
- Available parts 8.6 99
- Table stand 4092 99
- 8.7 Available parts 100
- Floor stand 4098 100
- Available parts 8.8 101
- Turnable unit 101
- 8.9 Available parts 102
- Wall Bracket 4093 102
- DK-7600 Struer 104
Related products and manuals for TVs & monitors Bang & Olufsen BeoVision 6
(60 pages)
(36 pages)© 2020, manymanuals.com. All rights reserved. | 1.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals