Bang & Olufsen BeoVision 6 Service Manual Page 32
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3.2 Adjustments and Repair tips
Adjustments
Adjustments described
Stand adjustment (if motorised stand connected).
Tuner take over, IF adjustment & FM sound adjustment.
Geometry check.
Picture check.
Sound adjustment, no adjustment possible.
Purpose of Adjustments
The content in the adjustment instructions are the following:
- Contains text and illustrations if needed.
- The correct sequence for adjusting the product.
- The correct procedure for the adjustment.
Illustrations of:
- Geometry measuring points.
General considerations
- Correct adjustment of all parameters can only be obtained by using special test
signals and equipment for light measurement.
- Factory settings will give the best result.
- Customer picture set up, brilliance, contrast and colour are obtained in the TV
SETUP – OPTIONS – PICTURE.
Picture adjustments
Brightness, contrast and colour can only be adjusted in the MENU – OPTIONS –
PICTURE.
The SERVICE MENU does not give this opportunity.
Measurements
All measurements concerning the geometry are measured with the contrast screen
mounted.
Measurements are performed with a ruler, or by counting pixels.
For the best result, measurements are performed in a straight angle to the LCD
panel, e.g. you see into the reflection of your own eye.
The television must be turned on for minimum 20 minutes before measurements
may be started.
This is due to the back light that first is at 90% level after 20 minutes.
The test signal is applied to the V.TAPE input, SCART connector, unless other is
specified.
Preparations before check and adjustment
1. Turn the television on.
2. The television must warn up for minium 20 minutes before adjustment may be
performed.
The back-light reaches 90% efficiency after app. 20 minutes.
3. Select the correct test picture.
4. Set the television in the correct FORMAT.
It is recommended to use the ServiceTool to down load the settings.
ABO-CENTER v/HENRIKSENS ELEKTRONIK
- BeoCenter 6 – 26 1
- Survey of modules 1.1 3
- Survey of modules 3
- 1.2 How to service 4
- How to service 4
- How to service 1.3 5
- 1.4 How to service 6
- How to service 1.5 7
- PIN-code 7
- 1.6 How to service 8
- Fault flow chart 2.1 9
- Fault flow chart 9
- 2.2 Fault flow chart 10
- Fault flow chart 2.3 11
- 2.4 Fault flow chart 12
- Fault flow chart 2.5 13
- 2.6 Fault flow chart 14
- Fault flow chart 2.7 15
- 2.8 Fault flow chart 16
- Fault flow chart 2.9 17
- 2.10 Fault flow chart 18
- Fault flow chart 2.11 19
- 2.12 Fault flow chart 20
- Fault flow chart 2.13 21
- 2.14 Fault flow chart 22
- Fault flow chart 2.15 23
- 2.16 Fault flow chart 24
- Fault flow chart 2.17 25
- 2.18 Fault flow chart 26
- Fault flow chart 2.19 27
- 2.20 Fault flow chart 28
- Fault flow chart 2.21 29
- 2.22 Fault flow chart 30
- Adjustments 32
- ServiceTool 37
- Service mode 4.1 41
- Service mode 41
- 4.2 Service mode 42
- CUSTOMER SERVICE MENU 42
- Service mode 4.3 43
- Service mode in general 43
- 4.4 Service mode 44
- Service mode 4.5 45
- 4.6 Service mode 46
- Service mode 4.7 47
- 4.8 Service mode 48
- Service mode 4.9 49
- 4.10 Service mode 50
- Service mode 4.11 51
- 4.12 Service mode 52
- Service mode 4.13 53
- 4.14 Service mode 54
- IC INFORMATION 55
- MSP 02170A48 55
- PICTP 00 55
- 4.16 4.164.16 56
- 15. Geometry check 58
- 12. Geometry check 59
- 5.4 Replacement of LCD 60
- - Remove all cables 61
- - Remove socket cover 61
- - Remove speaker cover 61
- Correct mounted! 61
- + 5.5 Mount servicestands 64
- - Remove screws 64
- 5.9Replace Main chassis 65
- - Remove LCD shield 66
- - Remove LCD plugs 66
- - Remove plug from scaler 66
- - Remove cover 66
- 5.11 67
- Replace Main chassis 67
- Menu - BeoSound 3200 68
- 1. Update Software 68
- 2. HDR-A backup 68
- 3. . . . 68
- 4. . . . 68
- 5.13Replace LCD 69
- 5.14 Replace LCD 70
- 5.15 71
- + 5.5 Mount service stands 73
- - Remove cables 73
- Attention! 74
- - Remove fan 77
- - Remove screw 77
- - Remove as shown 80
- - Placement of PCB51 80
- - Remove cable 81
- DVI-I plug 90
- Type survey 91
- Type survey 6.5 91
- Video Input formats 92
- 6.6 Video Input formats 92
- Wiring diagram 93
- Available parts 94
- Available parts 8.2 95
- Survey of screws and washers 96
- Available parts 8.4 97
- 8.5 Available parts 98
- Base 4090 98
- Available parts 8.6 99
- Table stand 4092 99
- 8.7 Available parts 100
- Floor stand 4098 100
- Available parts 8.8 101
- Turnable unit 101
- 8.9 Available parts 102
- Wall Bracket 4093 102
- DK-7600 Struer 104
Related products and manuals for TVs & monitors Bang & Olufsen BeoVision 6
(60 pages)
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.278 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals